HTTP configuration, Digi Port Authority–Remote management diagnostics and auto-discovery tool, SNMP (read/write)
Whats wireless iap serial#
An additional serial port can act as a pass-through port, allowing local devices to communicate with a slave unit without disrupting the serial-to-Ethernet connection.
Digi One IAP converts ASCII data from serial devices to Ethernet protocols. Multi-master access allows multiple masters to communicate with a single slave across protocols. Applications may communicate with the serial device using TCP/UDP or Digi’s patented RealPort® COM port redirector for remote native COM port access.ĭigi One IAP supports a variety of serial and Ethernet protocols, allowing users to bridge serial and Ethernet devices, or both. Serial server functionality built into Digi One IAP allows any serial device to be connected to a TCP/IP network. It is ideal for device management applications requiring specific industry protocol support. Users can IP enable a broad range of serial devices, as well as link two industrial devices. Low loss RF Cable, Cable length 0.Digi One® IAP combines reliable serial-to-Ethernet connectivity with protocol conversion and interoperability.
Low loss RF Cable, Cable length 10m, RP-SMA Female to RP-SMA Male connector Low loss RF Cable, Cable length 1.5m, SMA Female to RP-SMA Male connector Low loss RF Cable, Cable length 5m, N Male to RP-SMA Male connector Low loss RF Cable, Cable length 1.5m, N Male to RP-SMA Male connector Low loss RF Cable, Cable length 10m, N Male to RP-SMA Male connector Low loss RF Cable, Cable length 1.5m, N Male to N Male connector Low loss RF Cable, Cable length 5m, N Female to N Male connector Low loss RF Cable, Cable length 10m, N Male to N Male connector Low loss RF Cable, Cable length 1.5m, SMA Male to RP-SMA Male connector N Female magnetic antenna base with cable length 1.5m and RP-SMA Male connector N Female magnetic antenna base with cable length 10m and RP-SMA Male connector Rooftop/Outdoor High Performance Omni Antenna, 3G/4G, GPS/GLONASS applications, 5dBi max.,N Female connector Omni-directional High-gain Antenna, 2.4GHz, 7dBi max, N Male connector Omni-directional High-gain Antenna, 5GHz, 5dBi max, N Male connector Omni-directional High-gain Antenna, 5GHz, 12dBi max, N Female connector with wall-mount bracket Omni-directional High-gain Antenna, 5GHz, 10dBi max, N Male connector LED x 2, Green for port Link/Act at 100Mbps.ĭual DC inputs. Green On: Power is on and functioning Normally. WPA-PSK (256-bit key pre-shared key supported)ĪRP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, 802.1X, SNMP, STP WPA/WPA2:802.11i (WEP and AES encryption) IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM port of IAP-420+ġ0/100Base-T(X) Ports in RJ45 Auto MDI/MDIXįully compliant with IEEE 802.3af Power Device specificationġ x External reverse SMA-type antenna connector Event Warning by Syslog, Email, SNMP Trap.Support AP/Client/Bridge/AP-Client Mode.Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported.High Speed Air Connectivity: WLAN interface support up to 150 Mbps link speed.
Whats wireless iap series#
Therefore, IAP-420 / IAP-420+ series are one of the best communication solutions for wireless applications on the industrial network. feature on ETH1 which is fully compliant with IEEE802.3af PoE P.D. You are able to configure IAP-420 / IAP-420+ series by WEB interface via LAN port or WLAN interface. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode.
Whats wireless iap mac#
It supports 802.1X and MAC filters for security control. IAP-420 / IAP-420+ series are reliable 802.11 b/g/n WLAN Access Point with 2 ports LAN.